Pyrolysis can turn the mixed plastics recovered from end-of-life vehicles (ELVs) into a liquid product with several properties close to those of commercial diesel, and adding an iron-pillared clay catalyst can raise oil yields sharply. But a recent study finds that the catalyst mainly increases how much liquid is produced rather than shifting that liquid toward a higher proportion of diesel-range molecules — a distinction that matters for anyone weighing the process as a recycling route.
From shredder residue to component plastics
Thermal pyrolysis decomposes plastics at elevated temperatures in the absence of oxygen, breaking polymer chains into liquid, gaseous and solid products. Earlier work has shown that common automotive plastics such as low-density polyethylene (LDPE), high-density polyethylene (HDPE) and polypropylene (PP) can be converted into valuable hydrocarbons at relatively high yields. Much of that research, however, was built on automotive shredder residue, a heterogeneous mixture of plastics, metals, textiles and other materials.
That leaves less information about how plastics recovered directly from parts such as dashboards, bumpers and headlamps behave during pyrolysis. Automotive plastic waste (APW) can also carry mineral fillers, flame retardants, fiberglass and other additives that affect degradation behavior and product composition. To close that gap, the researchers first characterized plastics taken directly from ELVs instead of relying on mixed shredder residue.
The feedstock contained acrylonitrile butadiene styrene (ABS), HDPE, LDPE, PP, polystyrene (PS) and fiberglass, along with substantial volatile and ash fractions. Front and rear bumpers made up 86.6% of the sample by weight, and the fiberglass commonly used to reinforce automotive components contributed to the relatively high ash content.
An iron-pillared clay catalyst
Catalysts can improve pyrolysis by accelerating reactions, altering product distributions and potentially lowering the required temperature or residence time. Commercial zeolites have been studied widely, but lower-cost clay-based alternatives are drawing growing interest. Among these, pillared clays modified with metals such as iron, titanium or zirconium have shown potential to raise liquid yields and influence the formation of fuel-range hydrocarbons. Iron-modified clays are particularly attractive because they may improve oil production without relying on more expensive commercial catalysts.
Rather than using bentonite clay in its original form, the team modified it through iron pillaring — a process that introduces iron species into the clay structure and changes characteristics such as surface acidity and pore structure that can influence pyrolysis reactions. The researchers then compared thermal and catalytic pyrolysis across temperatures from roughly 350°C to 521°C and catalyst loadings of about 6% to 34% by weight, using a statistical experimental design that let them evaluate how temperature and catalyst concentration interact.
Yield gains, largely unchanged composition
The catalyst strongly affected liquid yield. Catalytic pyrolysis produced an average oil yield of about 68%, compared with 41% for thermal pyrolysis alone. The highest oil yield, 78.6%, was reached at approximately 416°C with a catalyst loading of about 24%.
Its influence on oil composition was much weaker. Thermal and catalytic pyrolysis produced similar proportions of hydrocarbons in the C8–C24 range associated with gasoline- and diesel-range compounds. In other words, the catalyst helped convert more of the plastic feedstock into liquid product, but did not substantially shift that liquid toward a higher share of diesel-range molecules.
Temperature, by contrast, had a greater effect on product composition. Lower pyrolysis temperatures favored diesel-range organics, while temperatures above 450°C produced a heavier, waxier oil.
Fuel properties and the gaps that remain
The resulting pyrolysis oil showed several properties comparable to those of commercial diesel. The researchers reported a calorific value of 49.85 MJ/kg, a flash point of 113°C and total aromatics of 3.55% by area — values within or comparable to ranges specified for conventional fuels. Branched heptenes and heptanes dominated the oil, compounds also identified in previous studies of polypropylene and automotive-plastic pyrolysis.
Not all properties met diesel specifications, however. Both density and viscosity exceeded the limits typically specified for diesel fuel, which the researchers attributed partly to heavier, long-chain hydrocarbon fractions remaining in the oil. Additional processing could therefore be required before the oil could be used as a diesel-range fuel. The team suggested approaches such as distillation and centrifugation, as well as optimizing reaction conditions through lower temperatures and longer residence times, to reduce heavier fractions and improve fuel properties.
What the study implies
Taken together, the results position pyrolysis as a technically promising route for recovering value from automotive plastics, while highlighting the development still required before broader commercial application. The catalyst's value lies mainly in throughput — more liquid per unit of feedstock — rather than in upgrading the fuel itself, and the findings suggest product quality depends more on temperature control and downstream separation than on the iron-modified clay.
Future work could investigate different iron concentrations in the catalyst, improve reactor designs and heat transfer, and combine pyrolysis with downstream distillation to separate gasoline- and diesel-range fractions.
Improved collection and sorting of automotive plastics will also be important. Without systematic removal and classification of plastic components from end-of-life vehicles, reliable data on the volume and composition of available automotive plastic waste remain limited. Better information on these waste streams would help researchers and recyclers assess feedstock availability and plan potential industrial-scale pyrolysis operations.
