Instruments & Meters

SinceVision Adds Wide-Spot Laser Sensor for Rough-Surface Displacement Measurement

Zorica IlicNovember 17, 20265 min read11 views

At a glance

  • The SGI-N030W combines an expanded laser spot with 50 kHz sampling to steady micrometre-level readings on textured materials and to gauge battery electrode thickness in line.
  • SinceVision has launched the SGI-N030W, a wide-spot laser displacement sensor that averages surface texture rather than resolving it, aimed at battery, semiconductor and precision assembly work. Company trials report thickness measurement within ±0.3 µm at a web speed of 300 mm/s using two synchronised heads.
Two laser displacement sensor heads on a granite-style gantry project widened light spots onto a moving metal foil web from opposite sides.

SinceVision has added the SGI-N030W to its SGI Series of laser displacement sensors, a wide-spot model intended for high-speed, non-contact dimensional measurement on rough, textured and irregular surfaces. The company says the sensor targets lithium-ion battery manufacturing, semiconductor processing and precision mechanical engineering, where repeatable micrometre-level measurement is required.

The design centres on an expanded laser spot used with optical triangulation. Conventional point-spot sensors concentrate reflected laser energy on a small area, so microscopic features such as scratches, grain boundaries, brushed textures and matte finishes can generate signal variations that the system interprets as dimensional change. According to SinceVision, this can produce false defect warnings and trigger additional inspection. The wide-spot configuration collects reflected light across a broader area and averages localised peaks and valleys before signal conversion, which the company says reduces the influence of surface roughness and optical scattering on materials including drawn metals, sandblasted surfaces and coated battery foils.

Specified performance

  • Reference distance of 30 mm with a measurement range of ±5 mm
  • Repeatability of 0.05 µm on a diffuse white target under static conditions
  • Linearity of ±0.02% of full scale across the measurement range
  • Sampling frequency of 50 kHz, equivalent to a 20 µs update interval
  • RS485 and 100Base-TX Ethernet, plus switchable analogue outputs of 4–20 mA current or 0–10 V voltage
  • Master-slave synchronisation, allowing two heads to operate in opposition on either side of a component or moving material

Battery electrode thickness in line

SinceVision identifies in-line thickness measurement of lithium-ion electrodes as a principal application. Coating thickness and uniformity influence energy density, internal resistance and long-term cell stability. Offline checks with contact micrometers or drop indicators can introduce operator variability and deform wet or uncured electrode material, while periodic spot readings cannot cover an entire production reel.

The proposed arrangement uses two synchronised sensors positioned above and below the moving electrode web, mounted on a calibrated low-thermal-expansion marble gantry. The opposing heads measure their respective clearances to the material, and a controller combines those readings with the fixed mounting datum to calculate absolute thickness in real time. SinceVision reports that production trials held measurement within ±0.3 µm at a web speed of 300 mm/s. At 50 kHz, the company says longitudinal resolution is sufficient to flag localised coating agglomerations, edge thinning and exposed substrate before the electrode proceeds to cell winding.

Semiconductor and assembly uses

In semiconductor manufacturing, the non-contact approach is intended for wafer position verification, edge detection, height measurement, and checks of wafer seating and chuck alignment in atmospheric transfer modules and vacuum load-lock systems. In precision assembly, the sensor can track voice coil motors, linear actuators and micro-steppers. Its 50 kHz rate is specified to capture transient displacement, mechanical oscillation, settling behaviour and end-stop overshoot across the full range, with position data passed to machine control systems over Ethernet.

Surface-related errors

Jack Li, Global Sales and Marketing Director at SinceVision, says false defect warnings caused by surface texture remain a recurring challenge in battery manufacturing and precision assembly. He says point-beam sensors can read microscopic scratches and rough coatings as actual thickness variation, slowing production lines and creating a need for extra manual inspection. He describes the expanded optical spot as designed to average out those surface-related variations, with synchronisation between opposing heads supporting high-speed thickness verification.

Reported by Zorica Ilic, Network Test, Infrastructure and Sourcing Editor.