Metals & Alloys

Zmag pitches permanent-magnet stirring, pumping and scrap submergence to aluminium casthouses

Hanna VirtanenNovember 10, 20265 min read2 views

At a glance

  • The company's zPMC permanent-magnet circuit underpins MagStir, MagPump and Typhoon, aimed at melt homogenisation, metal circulation and low-density scrap recovery.
  • Zmag America is positioning three permanent-magnet systems — MagStir, MagPump and Typhoon — as alternatives to immersed mechanical equipment for aluminium furnace stirring, circulation and scrap submergence, citing installations at NZAS, Boyne Smelters, TST and Neuman Aluminium. Wider uptake still depends on casthouses accepting an unfamiliar approach in a segment where ABB, Presezzi and Pyrotek already have established offerings.
Concept illustration of a magnetic unit drawing shredded aluminium scrap into a vortex beneath the surface of a melting furnace.

Aluminium casthouses seeking to raise their recycled-metal intake run into a practical limit: light scrap, machining chips and other low-density fractions are awkward to charge into conventional melting furnaces, and getting them beneath the melt surface without sacrificing recovery rates, melt quality or throughput is difficult. Zmag America, Ltd. is promoting a set of systems that handle stirring, circulation and scrap submergence using permanent-magnet circuits rather than components dipped into the molten bath.

The company's background lies in industrial magnetics: it traces its history to magnetic engineering work and the commercialisation of eddy-current separation, a technique for recovering non-ferrous metals from mixed streams. It later moved into molten-metal applications and developed its patented zPMC (Zmag Permanent Magnetic Circuit), the platform behind its stirring, pumping and submergence equipment.

The central distinction is between permanent-magnet and conventional electromagnetic stirring. Instead of an electromagnetic stirring arrangement, zPMC uses a permanent magnetic circuit to create the field that moves the metal. Zmag describes the resulting motion as a "virtual impeller", because circulation is generated without an immersed mechanical impeller. In an August 2025 interview with AL Circle, Zmag America president Eishin Takahashi named limited familiarity with the approach as one barrier to wider US adoption, noting that producers worldwide tend to be conservative and prefer equipment and processes they already know.

MagStir for furnace homogenisation

MagStir is a non-contact stirring system for melting and holding furnaces. It uses the permanent magnetic circuit to set the bath in motion, helping to even out temperature and alloy composition; Zmag offers configurations for furnaces from 15 to 200 metric tons. Because nothing is immersed, casthouses can add circulation without putting extra moving parts into the molten-metal environment. New Zealand Aluminium Smelters fitted the system in a casting furnace and later extended it to other furnaces; a technical case study published in 2017 reported better temperature control during furnace preparation. A MagStir unit was also installed at Rio Tinto's Boyne Smelters in Queensland, Australia, in 2019.

MagPump as a mechanical-pump alternative

MagPump applies the same principle to pumping and circulation. It is designed to drop into a standard pump well without furnace modification, uses no physical impeller and is marketed as an almost hands-free unit with no consumable parts and minimal downtime. At the TANDEM Division of US secondary producer TST Inc. in Fontana, California, it replaced a mechanical pump during a seven-week trial. The account describes smooth running and less disturbance of the metal surface, and TST plant management reported that the system avoided the splashing seen with conventional pumping as the furnace level dropped during draining. The technology was also presented at TMS 2023, where its use in side-well, multi-chamber furnaces was discussed alongside potential roles in gas injection and scrap submergence.

Typhoon targets hard-to-process scrap

Typhoon concentrates on scrap submergence and chip melting, pulling light scrap and machining chips under the surface instead of letting them float on top. Its magnetic circuit creates a vortex-like flow that draws material into the melt, supporting heat exchange and recovery. At Neuman Aluminium's Marktl plant in Austria, the system was built into a furnace modernisation intended to widen the use of low-density post-consumer scrap, including fractions with a bulk density of about 375 kg/m³. Neuman had targeted one metric ton per hour while the furnace continued melting solid charge; in operation the unit processed close to twice the planned quantity within the expected time without disrupting normal running, with low operator involvement and, according to the company, no adverse effect on melt or finished-product quality. The published account puts Typhoon's power draw at 5–15 kW including its air-cooling blower, with capacity to submerge up to five metric tons of chips per hour and adjustable vortex intensity that can keep the bath moving between charges.

A crowded technology field

Several established suppliers compete in furnace stirring, metal circulation and scrap submergence, though not all offer direct equivalents. ABB's AL-EMS electromagnetic stirring system has more than 430 installations, the company reports, and in April 2026 ABB announced a further order from Arconic for a fifth stirrer at its Hungarian casthouse. Presezzi Extrusion Group's Melting Technology division offers the L.E.C. stirrer for melting and holding furnaces. Pyrotek covers electromagnetic pump systems and LOTUSS low-turbulence scrap submergence, which pairs a circulation pump with a refractory well. Rockwell Automation sits in the adjacent automation segment, supplying furnace and ladle-shop controls.

How quickly permanent-magnet designs displace immersed mechanical equipment remains open. The case presented rests on reduced exposure of hardware to molten aluminium and on handling scrap that conventional furnaces struggle to charge; wider uptake, by Takahashi's account, depends partly on producers growing comfortable with an unfamiliar approach as their recycled feedstock becomes more demanding.

Reported by Hanna Virtanen, Cutting, Abrasives and Welding Editor.